How To Turn Off Seat Belt Alarm Jeep Grand Cherokee
Download Article
Download Article
It is common knowledge that you should wear your seat belt while driving. Yet, there are many situations where a factory seat chugalug alarm can get a nuisance. For example, if y'all are driving on a farm at low speeds with many stops, you lot may not demand a seat belt. More urban situations, such equally taking your wallet out in a drive-through or letting your dog ride shotgun, can too be unpleasant with a abiding ding. Sometimes, it is even possible for the alarm to get "stuck" and ding constantly whether you are buckled or non. Luckily, it is usually possible to disable this seat belt alarm.
-
1
Beware of the airbag risk. On many cars, the seat belt sensor is also used to trigger the airbag. Investigate whether this is the case on your car before doing anything drastic to your seat chugalug alert.
-
2
Cheque the user transmission or ask your reseller to disable it per software. Almost all manuals requite instructions on how to disarm the seat belt alarm without cutting any wires. This usually consists of doing a series of tasks in the car while parked. As an example, the sequence for turning off the seat belt alarm on a Toyota Camry (2004 and newer) is given below.[1]
- Insert the key and turn the ability on. You lot should not crank the engine.
- There is a knob on your dash panel that toggles your trip and total odometer readings. Press this knob until you see "ODO" on the instrument panel.
- You should turn the key off, and so back on.[two]
- Agree the same knob for x-xv seconds. While still property the knob, put on your seatbelt, and then release the knob.
- You lot should meet "B OFF" flash on the instrument panel. This indicates that you lot turned off your seat belt alarm.
Advertisement
-
iii
Disable your alarm. This may mean following the steps in the owner's manual for reprogramming your alert, which, equally described above, is often a series of actions taken while the car is parked.[three] Alternatively, you can take the vehicle to your dealer to do this. Some vehicles may take to go to the dealer to exist reprogrammed with specific software.
- Information technology is worth noting that dealerships are often reluctant to fulfill this request due to legal and liability bug. Still, this is the safest method of disabling your seat belt alarm, and dealerships will make reasonable adjustments in special cases.[4]
Advertisement
-
one
Go an unattached seat belt clip if you lot don't plan to utilize the seat belt. At that place are two basic products on the market that are referred to equally a seat belt alarm stopper. The starting time is simply an unattached seat belt clip that can be inserted into the receptacle. The safest way to use this choice is to source a seat belt clip, or natural language, that matches your original seatbelt exactly. You tin can look for i at a scrap yard or parts store.
- Measure the overall dimensions of the clip's exposed metallic section, also as the dimensions of your receptor.
- Remember that driving without using a seatbelt is very unsafe, and against the police force in most areas.
-
2
Purchase an extender if yous plan to use the seatbelt. The other stopper selection, chosen an extender, is a slice that clips into the receptacle, merely as well provides an boosted receptacle then that you tin can use your seat chugalug without removing the alert stopper. You should purchase your extender from the original equipment manufacturer of the seat belt, and it must run across the criteria in its operating transmission, including mass and stature.[5]
- Following the criteria for your extender is of import considering your seat chugalug system needs to pass an anchorage pull exam, which ensures that it can withstand crash-level forces. You lot can discover these requirements online or by asking your seat chugalug manufacturer.
-
three
Install the seat chugalug alarm stopper. Make certain that your stopper fits your seat belt receptacle. So, simply click the stopper into your receptacle. You are now free of the dinging alarm sounds.
Advertising
Add New Question
-
Question
Tin a seat chugalug cause the airbag low-cal to always be on?
Yep. To verify if they're connected, attempt looking under your seat. The connector for the seat belt lock volition often be a brilliant color, and if yous encounter it, that means it'south connected to the airbags. However, non all motorcar models will have this characteristic. If you're non sure, accept your automobile to the dealership or inquire your manufacturer.
Inquire a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
-
You might need a flashlight to run into better under the seat.
-
Drive your vehicle afterwards to bank check if it worked; if you lot cut the wrong wires, just use butt connectors to re-connect them.
-
Information technology should brand no departure whether the belt was plugged in while yous do this, merely it may be dissimilar on the different varieties of vehicles.
Advertisement
-
Tampering with the seat belts will void your warranty.
-
Exercise non attempt to cut the buckle harness. This volition likely disable the front end rider airbag. In some cars, cut this cable volition as well accept the opposite effect that you want, forcing the seat belt warning to stay on constantly.
-
Information technology'south not recommended to effort to featherbed the alarm inside the seat chugalug buckle. Some seat belts comprise pyrotechnic devices that can detonate if tampered with, and removing or tampering with the pieces inside can outcome in the seat chugalug releasing during a crash.
-
Tampering with your seat belt sensor in any way can affect airbag performance. This can put you lot and/or your passengers at serious risk. Exist sure that your airbags volition not be affected before altering your seat belt warning sensor.
Advertisement
Things You lot'll Demand
Installing a Seat Belt Alert Stopper
- Seat Chugalug Alert Stopper or Extender
Disabling the Seat Belt Alarm with Manufacturer's Tools
- Owner's Manual
- Software Update (if needed/bachelor)
About This Article
Commodity Summary X
To stop a seat belt warning from going off, you tin can purchase a seat belt alarm stopper at a bit grand or from the manufacturer. One option is to purchase an unattached clip that is inserted into the seat chugalug receptacle and will stop the alarm from going off. The other is an extender that provides an additional seat belt receptacle, which allows the user to fasten their seat belt while stopping the alarm. To disable the warning without cutting whatever wires, check the motorcar's user manual for instructions or ask your reseller to disable it using software. For more tips on stopping your seat belt warning safely, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 748,224 times.
Did this article help you?
Source: https://www.wikihow.com/Disable-a-Seat-Belt-Alarm
0 Response to "How To Turn Off Seat Belt Alarm Jeep Grand Cherokee"
Post a Comment